Displays information about the PIM-SM interface setup on the switch.
show ip pim interface gigabitethernet [{slot/port[/sub-port][-slot/port[/sub-port]][,...][slot/all][all]}]
show ip pim interface vlan <1-4059>
Identifies the slot and port in one of the following formats:
a single slot and port (slot/port)
a range of slots and ports (slot/port-slot/port)
a series of slots and ports (slot/port,slot/port,slot/port)
all ports on the same slot (slot/all)
all ports on the switch (all)
Specifies the VLAN ID in the range of 1 to 4059. By default, VLAN IDs 1 to 4059 are configurable and the system reserves VLAN IDs 4060 to 4094 for internal use. On switches that support the vrf-scaling and spbm-config-mode boot configuration flags, if you enable these flags, the system also reserves VLAN IDs 3500 to 3998. VLAN ID 1 is the default VLAN and you cannot create or delete VLAN ID 1.
None
User EXEC
The show ip pim interface command displays the following information:
|
Output field |
Description |
|---|---|
|
IF |
Indicates the slot and port number or VLAN ID of the interface where PIM is enabled. |
|
ADDR |
Shows the IP address of the PIM interface. |
|
MASK |
Shows the network mask for the IP address of the PIM interface. |
|
MODE |
Indicates the configured mode of this interface. The valid modes are SSM and Sparse. |
|
DR |
Shows the designated router (DR) for this interface. |
|
HLINT |
Specifies how long to wait (in seconds) before the PIM router sends out the next hello message to neighboring switches. The default hello interval is 30 seconds. |
|
JPINT |
Specifies how long to wait (in seconds) before the PIM router sends out the next join or prune message to its upstream neighbors. The default join and prune interval is 60 seconds. |
|
CBSPR |
Specifies the preference for this local interface to become a C-BSR. The C-BSR with the highest BSR priority and address the preferred BSR. The default is –1, which indicates that the current interface is not a C-BSR. |
|
OPSTAT |
Indicates the status of PIM on this interface: up or down. |
|
INTF TYPE |
Indicates whether the PIM interface is active or passive. |
|
VLAN-ID or PORT-NUM |
Indicates the slot and port number or VLAN ID of the interface where PIM is enabled. |
|
PIM ENABLE |
Indicates the administrative status of PIM. |
|
MODE |
Indicates the configured mode of this interface. The valid modes are SSM and Sparse. |
|
HELLOINT |
Specifies how long to wait (in seconds) before the PIM router sends out the next hello message to neighboring switches. The default hello interval is 30 seconds. |
|
JPINT |
Specifies how long to wait (in seconds) before the PIM router sends out the next join or prune message to its upstream neighbors. The default join and prune interval is 60 seconds. |
|
CBSRPREF |
Specifies the preference for this local interface to become a C-BSR. The C-BSR with the highest BSR priority and address the preferred BSR. The default is –1, which indicates that the current interface is not a C-BSR. |
|
INTF TYPE |
Indicates whether the PIM interface is active or passive. |
The following example displays information about the PIM-SM interface configuration on the switch.
Switch:1>show ip pim interface
================================================================================
Pim Interface - GlobalRouter
================================================================================
IF ADDR MASK MODE DR HLINT JPINT CBSPR OPSTAT INTF TYPE
Port1/4 10.1.1.1 255.255.255.0 ssm 10.1.1.1 30 60 -1 (disabled) up active
Clip1 111.10.10.10 255.255.255.255 ssm 111.10.10.10 30 60 11 (enabled) up passive
Vlan300 21.0.0.206 255.255.255.0 ssm 21.0.0.206 30 60 -1 (disabled) up active
Vlan400 41.0.0.206 255.255.255.0 ssm 41.0.0.206 30 60 -1 (disabled) up active
Vlan500 31.0.0.206 255.255.255.0 ssm 31.0.0.206 30 60 -1 (disabled) up active
Vlan700 62.0.0.206 255.255.255.0 ssm 62.0.0.206 30 60 -1 (disabled) up active
Vlan701 62.0.1.206 255.255.255.0 ssm 62.0.1.206 30 60 -1 (disabled) up active
Vlan702 62.0.2.206 255.255.255.0 ssm 62.0.2.206 30 60 -1 (disabled) up active
Vlan703 62.0.3.206 255.255.255.0 ssm 62.0.3.206 30 60 -1 (disabled) up active
Switch:1>show ip pim interface vlan 10
========================================================================
Vlan Ip Pim
========================================================================
VLAN-ID PIM-ENABLE MODE HELLOINT JPINT CBSRPREF INTF TYPE
------------------------------------------------------------------------
10 enable sparse 30 60 -1 (disabled) active